Part 3 video and biggest upgrade so far!
If you want to purchase this 3D printer here is link:
Anet A8 EU plug: https://goo.gl/kCzYvN
Anet A8 US plug: https://goo.gl/34WWUX
E3D V6 Hotend upgrade https://goo.gl/xbjjL5
GearBest.com — https://goo.gl/pqKf6h
Banggood.com — https://goo.gl/9CpYMJ
Aliexpress.com — https://goo.gl/C8ndaT
3D printers parts and supplies https://goo.gl/NXVL7M
Cheap filaments PLA filament https://goo.gl/D9jY9v
ABS Filament https://goo.gl/DBL1ok
Flexible filament — https://goo.gl/1DMTJf
Premium/special quality filaments
APRINTAPRO shop https://goo.gl/sgXkAW
PrintaFix adhesion SPRAY https://goo.gl/Fr9tmU
Heat bed mosfet module — https://goo.gl/91i7bQ
3D printing surface: Sticker: https://goo.gl/WTmmiM
Glass: https://goo.gl/3GqP6Z
BueTape: https://goo.gl/7vQMYp
Switch for PSU https://goo.gl/sKzzkg
Rubber Timing Belt https://goo.gl/3xtQPv
SCS8UU-8mm-Linear-Ball-Bearing https://goo.gl/88pgGV
Insulation material: https://goo.gl/5Qbtve
Micro SD To SD Card Extension Cable https://goo.gl/zgKzrz
All links to upgrades, parts and G codes are down below!
E3Dv6 Anet A8
http://www.thingiverse.com/thing:1632847
Just X-carrige! Take just one part (X-carrige)
http://www.thingiverse.com/thing:1196…
MK8 motor mount for bowden on Anet A8
https://www.thingiverse.com/thing:203…
E3D v6 Fan Duct
http://www.thingiverse.com/thing:547325
Anet A8 X-Idler Mounts If need it
http://www.thingiverse.com/thing:1919544
E3D V6 Hot End Full Kit 1.75mm
http://www.gearbest.com/3d-printer-pa…
Heated Bed 220×220 mm Insulation
https://www.aliexpress.com/item/4pcs-…
SpoolHolder ANET A8
http://www.thingiverse.com/thing:1624641
Fiber Glass Reinforced Rubber Timing Belt
http://www.ebay.com/itm/141938661911
…………………..CODES…………………………
Start G codes
G21 ;metric values
G90 ;absolute positioning
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 X-16 Y-26 E3000
G28 Z0 ;move Z to min endstops
G1 Z15.0 F(travel_speed) ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F(travel_speed)
M117 Printing…
End code
M104 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F(travel_speed) ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
// Travel limits after homing
#define X_MAX_POS 220
#define X_MIN_POS -28
#define Y_MAX_POS 220
#define Y_MIN_POS -12
#define Z_MAX_POS 230
#define Z_MIN_POS 0